Gas Metal Arc Welding of Austentic Stainless Steel (M-8 or P-8) 10 through 18 Gage, in the as-Welded Condition, with or without Backing
标准号:ANSI/AWS B2.1-8-005-2002
标准名称: 在焊接条件下、有或没有垫板、10到18规格的奥氏体不锈钢(M-8或P-8)的气体保护金属极电弧焊
英文名称:Gas Metal Arc Welding of Austentic Stainless Steel (M-8 or P-8) 10 through 18 Gage, in the as-Welded Condition, with or without Backing
标准类型:国外标准
标准状态:现行
中国标准分类号(CCS):J33
国际标准分类号(ICS):25.160.10
ANSI/AWS B2.1-8-013-2002 现行
标准焊接程序规范.在焊接条件下、有或没有垫板、10到18规格的奥氏体不锈钢(M-8/P-8)的保护金属电弧焊
ANSI/AWS B2.1-8-009-2002 现行
在焊接条件下、有或没有垫板、10到18规格的不锈钢(M-8或P-8)的钨电极惰性气体保护焊
AWS B2.1-8-005 ERTA-2004 现行
带或不带支持,在焊接条件下18到10计(M-8,P-8和S-8)奥氏体不锈钢的(短电路转移模式)气体金属焊接的标准焊接程序规范
ANSI/AWS B2.1-1/8-228-2002 现行
碳钢与奥氏体不锈钢屏蔽金属电弧焊(从M-1/P-1/S-1,组1或组2焊接到M-8/P-8/S-8, 组1)1/8到1-1/2英寸厚,ER309-15、16或17一级管道设备焊接条件下的焊接程序规范(WPS)
ANSI/AWS B2.1-1/8-229-2002 现行
碳钢与奥氏体不锈钢气体钨电弧焊(从M-1/P-1/S-1,组1或组2焊接到M- 8/P-8/S-8, 组1)1/8到1-1/2英寸厚ER309、ER309-15、16或17一级管道设备焊接条件下的焊接程序规范(WPS)
ANSI/AWS B2.1-1/8-006-2002 现行
在焊接条件下、有或没有垫板、10到18规格的碳钢与奥氏体不锈钢(M-1至M-18,或P-8)的气体保护金属极电弧焊
ANSI/AWS B2.1-1/8-230-2002 现行
气体保护钨极弧焊的标准焊接程序规范(WPS),可熔嵌入根部的,碳钢与奥氏体不锈钢(M-1/P-1/S-1, 组 1 和 2 焊到 M-8/P-8/S-8, 组 1) 1/16 至 1-1/2 英寸厚, IN309 和 ER309, 焊接状态,主要是管道设施
ANSI/AWS B2.1-1/8-014-2002 现行
标准焊接程序规范.在焊接条件下、有或没有垫板、10到18规格的碳钢与奥氏体不锈钢(M-1至M-18,或P-8)的保护金属电弧焊
ANSI/AWS B2.1-1/8-227-2002 现行
利用轻便仪器测量立体声播放系统震动衰减特性的方法
ANSI/AWS B2.1-8-215-2012 现行
标准焊接程序规范(WPS).主要用于管道的,在 IN3XX和ER3XX焊接条件下、1/8到1-1/2英寸厚的自耗嵌入式奥氏体不锈钢(M-8/P-8/S-8,组1)钨电极惰性气体保护焊